flexcell FX-5000 Скачать руководство пользователя страница 5

 

F

LEXCELL

®

 

I

NTERNATIONAL 

C

ORPORATION

 

 

iv 

FEDERAL COMMUNICATIONS COMMISSION 

RADIO FREQUENCY INTERFERENCE STATEMENT 

 

 

 

This computing equipment has been type-tested and found to comply with the limits for a Class B digital 

device in accordance with the specifications for Subpart J of Part 15 of FCC Rules. These limits are 

designed to provide reasonable protection against harmful radio and TV interference in a residential 

installation. There is no guarantee that interference will not occur in a particular installation. 

 

The following instructions and precautions must be observed by the user when installing and operating this 

device: 

 

1.

 

The equipment must be operated in strict accordance with the manufacturer's 

instructions. 

2.

 

The unit(s) must be plugged into a properly-grounded power outlet and used with the 

power cord supplied with the unit(s), unmodified. 

3.

 

The unit must be operated with the factory-installed cover in place. 

4.

 

No modifications of the equipment can be made which may result in the equipment 

failing to meet the limits of the FCC Rules. 

5.

 

The equipment must be maintained in a satisfactory state of repair. 

6.

 

Shielded cables must be used with this equipment to ensure compliance with the FCC 

Rules. 

 

 

If the unit interferes with radio or television reception (which can be tested by turning the unit off and on) 

the user is encouraged to try the following procedure to correct the interference: 

 

1.

 

Reorient the antenna of the receiver. 

2.

 

Relocate the equipment to increase the distance between the unit and the radio/TV. 

3.

 

Connect the unit to an outlet on a different circuit from the receiver. 

4.

 

Consult with the dealer or an experienced radio/TV technician for advice on ways to 

reduce interference. 

 

 

 

Содержание FX-5000
































Отзывы: