FläktGroup Semco NEUTON Скачать руководство пользователя страница 19

Страница: 19 / 28

OWNER’S MANUAL

NEUTON™

POINTS LIST

KEYPAD

The BACview

keypad (

See Figure 9

) can be used to adjust setup parameters . The keypad can plug directly into the

bottom of the wall mount sensor (

See Figure 10

) or directly into the I/O Zone 583 Controller . If the CO

option on the

sensor is included, it may be necessary to plug the BACview

directly into the I/O Zone 583 controller, and disconnect

the wall mount sensor at the controller while the BACview is being used .

FIGURE 9.

BACview

Keypad (Optional - not

included with module)

FIGURE 10.

Plug the

BACview

keypad directly

into the bottom of the ZS
Pro Sensor zone controller .

Name

Description

Type

Object ID

Device ID

Object Name

Exp:-

Num

I/O Type

Setpoint /

Cooling Occupied

Setpoint

Status of occupied cooling setpoint read

from the Zone Sensor and after limits

applied by BAS . Effective setpoint in use

by controller .

BAV

AV:20

DEV:2402

occ_clg_sp_1

Setpoint

/ Heating

Occupied

Setpoint

Status of occupied heating setpoint read

from the Zone Sensor and after limits

applied by BAS . Effective setpoint in use

by controller .

BAV

AV:21

DEV:2402

occ_htg_sp_1

Setpoint

/ Cooling

Unoccupied

Setpoint

Status of unoccupied cooling setpoint

read from the Zone Sensor and after

limits applied by BAS . Effective setpoint

in use by controller .

BAV

AV:22

DEV:2402

unocc_clg_sp_1

Setpoint

/ Heating

Unoccupied

Setpoint

Status of unoccupied heating setpoint

read from the Zone Sensor and after

limits applied by BAS . Effective setpoint

in use by controller .

BAV

AV:23

DEV:2402

unocc_htg_sp_1

Setpoint /

Cooling Setpoint

Adjust

not used - inaccessible Setblock block

internal value

BAV

AV:16

DEV:2402

clg_adj_1

Setpoint /

Heating Setpoint

Adjust

not used - inaccessible Setblock block

internal value

BAV

AV:19

DEV:2402

htg_adj_1

Setpoint /

Effective Cooling

Setpoint

not used - inaccessible Setblock block

internal value

BAV

AV:17

DEV:2402

eff_clg_sp_1

Setpoint /

Effective Heating

Setpoint

not used - inaccessible Setblock block

internal value

BAV

AV:18

DEV:2402

eff_htg_sp_1

water temp

Loop water temperature sensor wired to

analog input #4

BAI

AI:1

DEV:2402

water_temp_1

0:04

Thermistor

Zone CO2

CO2 value from Zone Sensor

ASVI

AI:2

DEV:2402

zone_co2_1

Содержание Semco NEUTON





























Результаты поиска

Содержание Semco NEUTON

Отзывы:

Похожие инструкции для Semco NEUTON

Бренды по названию

Популярные бренды

FläktGroup Semco NEUTON, Руководство пользователя

Результаты поиска

Содержание Semco NEUTON

Отзывы:

Похожие инструкции для Semco NEUTON

Бренды по названию

Популярные бренды