background image

Connector 4 (CN4), 20-Pin:  Programmable Output Connector (POC)

IMPORTANT: 

 

Odd Pin numbers 1 through 17 are programmable for up to 19 different output types.  

Refer to Special Option Group 2 for complete details.

Pin 1  Blue - 250mA negative (-) output when armed and during remote start (while running). This wire has  
 

a connector and must plug into same wire at the starter-kill relay. Caution:  When this wire is being    

 

used to trigger aftermarket accessories it must be diode isolated. 

Pin 2   Not Used 

Pin 3  Green/White [POC 1] - Parking light 250mA negative (-) output. The proper wire will test (-) when    
 

the parking light switch is in the on position.

Pin 4  Not Used

Pin 5   Red/Black [POC 2] - Auxiliary 5 250mA negative (-) output. This is an optional output that will  

 

 

provide a programmable output to trigger sliding doors, power windows or whatever other features    

 

you’d like.

Pin 6   Light Blue/White - Foot brake (+) input. This is used for option 1-09: Igniton controlled door locks 
 

setting 2 which will let the doors lock when brake is pressed.

Pin 7  Green [POC 3] - Auxiliary 4 250mA negative (-) output. This is an optional output that will provide a  
 

programmable output to trigger sliding doors, power windows or whatever other features you’d like.

Pin 8  Violet/Black - Trunk negative (-) input. This is an optional input that will monitor when the vehicle’s    
 

trunk has been opened. The proper wire will provide a (-) trigger while the trunk is open.

Pin 9  White/Black [POC 4] - Auxiliary 3 250mA negative (-) output. This is an optional output that will  

 

 

provide a programmable output to trigger sliding doors, power windows or whatever other features    

 

you’d like.

Pin 10  Red/White - Door trigger input. This wire monitors negative (-) or positive (+) trigger door-pins. The   
 

proper wire will provide a (-) trigger or a (+) trigger only when the doors are opened. You will  

 

need to test the wire for proper polarity and set door dip switch on the control module for the 

 

corresponding polarity.

Connector 3 (CN3) , 20 Pin Blade Connector - New Generation

This connector is used only if you are installing a Blade-AL or Blade-TB. The wiring harness for this 
connector also comes with the Blade cartridge. Please refer to the Blade install guide for wire description.  
The new generation 20 pin Blade connector now has a locking tab. The old connector with out a locking 
tab is compatible but you must modify the connector.

CM6300

 

Install Guide

Alarm System

www.firstechonline.com | www.compustar.com

Copyright 2012 Firstech, LLC.

Page 15

Содержание CM6300

































Отзывы: