background image

   

 

Special Option Groups 1 & 2

                                                CM6300

IMPORTANT:  The OP500 is required to change settings in Special Option Groups 1 and 2.

Special Option Group 1

Aux 1 Output Timing – Option 4-01 must first be set to setting 4. This special option allows a  

 

 

specific output duration for Aux 1 to be programmed.

Aux 2 Output Timing – Option 4-02 must first be set to setting 4. This special option allows a  

 

 

specific output duration for Aux 2 to be programmed.

4-8 

Aux 3 – 7 Output Timing – Option 3-11 must first be set to setting 2 and the optional Auxiliary  

 

 

settings module must be used. These special options allow specific output durations to be set for Aux  

 

3 – 7. Only available with 2 Way LCD remotes.

Special Option Group 2

This special option group allows you to determine the output type of the POC wires on CN2. For example, 
if you want to set POC #5 (default setting status out) to Aux 1, you will need change special option 5 to 
number 10. This must be done with the OP500.

   

 

Option Programming            

                                               CM6300

Option Programming Using the OP500 (programmer)

The OP500 can be used to program any available option. It is required to program options in Special 
Option Groups 1 and 2.    

STEP 1:

 

Make sure system is unlocked/disarmed. 

Using the blue or black 6 pin connector on 

the top of the OP500, connect it to the control module via the antenna wire. (Use the included extension 
cable if necessary.) Once connected, the OP500 will power up as long as the main ignition harness to the 
controller has been connected properly. 

STEP 2: 

To change the option number you wish to program, use the left and right arrow keys on the 

OP500. It will scroll through the options available in menu 1 and then move to menu 2, then 3 and 4. Use 
the up and down arrow buttons on the OP500 to adjust the option settings; “1” is the default setting, and 
“2”, “3”, and “4” are the optional settings.

CM6300

 

Install Guide

Alarm System

www.firstechonline.com | www.compustar.com

Copyright 2012 Firstech, LLC.

Page 27

Содержание CM6300

































Отзывы: