Filtec FT-50c Скачать руководство пользователя страница 235

Страница: 235 / 239

FT-50 Fill Level Inspector Service Manual

10-10

LED Definitions

Section 1, Bank 1: S2-7 = Closed/S2-8 = Closed

Section 1, Bank 2: S2-7 = Closed/S2-8 = Open

This section is used when the Label Inspection Option is installed
in your FT-50. For More information refer to your Label Inspection
Manual.

LED 1

Fault Error Present: The LED is on when there is a Fault
Alarm or other error in the system.

LED 2

Reject Pulse: Flashes one time for each container rejected.

LED 3

High Res Encoder Pulse: Flashes once for each pulse.

LED 4

Not used in this configuration.

LED 5

Slat Backup Sensor: Indicator lights when the sensor is
activated or when sensor is blocked.

LED 6

Bulged End Trigger: Indicator lights when the High Cap
sensor is activated or when sensor is blocked.

LED 7

Missing Lid Trigger: Indicator lights when the Missing Cap
sensor is activated or when lid is present.

LED 8

Inspect Trigger: Indicator lights when the Inspection Trigger
sensor is activated or when the sensor is blocked.

LED 9

AC Power Low: Indicator lights when the input AC power to
the FT-50 is too low to operate satisfactorily (below 70 VAC).

LED 10

+5 VDC Power Low: Indicator lights when the +5 VDC power
supply is too low to operate satisfactorily (below 4.85 VDC).
Indicator is also on when the Reset button is pressed.

LED 11

Detector: Used to get a coarse calibration setting for the Solid
State Detector.

Industrial Dynamics Company, Ltd. Document 40255-0600

Содержание FT-50c
















































































































































































































































Результаты поиска

Содержание FT-50c

Отзывы:

Бренды по названию

Популярные бренды

Filtec FT-50c, Сервисное и техническое руководство

Результаты поиска

Содержание FT-50c

Отзывы:

Бренды по названию

Популярные бренды