Filtec FT-50c Скачать руководство пользователя страница 165 | Manualshive

Страница: 165 / 239

Filtec FT-50c Скачать руководство пользователя страница 165

FT-50 Fill Level Inspector Service Manual

6-26

The Line Speed Calibration Procedure

1.

Press Key 5 until SYSTEM DISPLAY appears and then press
the Arrow Key to enter the Calibrate Mode. You may be
required to enter a password if your system is password
protected.

2.

Press Key 4 until REJECTOR STATUS appears and check to be
sure the rejector is activated. If it is turned off, press the Arrow
Key to turn it on.

3.

Open dip switch S1-5.

4.

Press Key 5 until REJECTOR TYPE appears and use the Arrow
Key to select the type of Proline rejector installed in your
system.

Note

This procedure is only applicable to systems utilizing a Proline
rejector. If you are using a rejector other than a Proline, you must
use the variable speed production line calibration procedures.

5.

Measure the distance in millimeters from the trigger sensor
beam to the centerline of the rejector. Accurate measurement is
extremely important for proper calibration.

6.

Press Key 4 until INSPECT TRIG TO C/L REJ appears and use
the Arrow Key to enter the measurement in millimeters.

7.

Measure the diameter of a production container (in milli-
meters) at the point where the container intersects the trigger
beam. This is the containers can width at the trigger point.

8.

Press Key 5 until CAN WIDTH AT TRIG appears and enter (in
millimeters) the production container’s width at the trigger
point.

9.

Measure the diameter of the container (in millimeters) at its
widest point. This is the containers maximum diameter.

10.

Press Key 5 until MAXIMUM CAN DIAMETER appears and
enter (in millimeters) the production container’s maximum
diameter.

11.

Press Key 5 until MAXIMUM LINE SPEED appears and enter
the line speed (in cpm) for the container in use. The program
assumes 12 mm container spacing in order to perform prelim-
inary calculations.

Industrial Dynamics Company, Ltd. Document 40255-0600

«
...
163
164
165
166
167
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды