Filtec FT-50c Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 239

Filtec FT-50c Скачать руководство пользователя страница 128

Chapter 5: System Software

5-33

Missing Lid

Prepares the FT-50 software for Missing Lid inspection by inserting
the necessary options into the software. When set to Not Present it
removes the options necessary for Missing Lid inspection from the
software.

This function does not activate or deactivate Missing Lid
inspection, it only readies the machine. To turn Missing Lid
inspection on or off you must use the Missing Lid Status function.

Missing Lid Text

Allows you to create a custom name for the Missing Lid Option.
Any instance in which “Missing Lid” would have appeared in the
software, is replaced by the custom label you created. The
following options are effected:

•

Missing Lid Status

•

Total Missing Lid

•

Reset Missing Lid

•

Alarm Missing Lid

•

Missing Lid Text

•

Missing Lid

Note

This manual assumes the default name for this option. If you
change the default text remember to substitute the new name
when reading this manual. To avoid confusion record the change
in the manual.

To create a name:

1.

Press the Arrow Key until the desired character appears.

2.

Press Key 6 to advance to the next space.

3.

Repeat steps 1 and 2 until you complete the entry and then
press Key 5 once to enter the text.

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
126
127
128
129
130
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды