Filtec FT-50c Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 239

Filtec FT-50c Скачать руководство пользователя страница 131

FT-50 Fill Level Inspector Service Manual

5-36

Diameter Missing Lid

Prepares the FT-50 software for Diameter Missing Lid inspection
by inserting the necessary options into the software. When set to
Not Present it removes the options necessary for Diameter Missing
Lid inspection from the software.

This function does not activate or deactivate diameter missing lid
inspection, it only readies the machine. To turn diameter missing
lid inspection on or off you must use the Diameter Missing Lid
Status function.

Diameter Missing Lid Text

Allows you to create a custom name for the Diameter Missing Lid
Option. Any instance in which “Diameter Missing Lid” would
have appeared in the software, is replaced by the custom label you
created. The following options are effected:

•

Dia Missing Lid Status

•

Total Dia Missing Lid

•

Reset Dia Missing Lid

•

Dia Missing Lid Width

•

Minimum Diameter Missing Lid

•

Alarm Dia Missing Lid

•

Dia Missing Lid Text

•

Dia Missing Lid

Note

This manual assumes the default name for this option. If you
change the default text remember to substitute the new name
when reading this manual. To avoid confusion record the change
in the manual.

To create a name:

1.

Press the Arrow Key until the desired character appears.

2.

Press Key 6 to advance to the next space.

3.

Repeat steps 1 and 2 until you complete the entry and then
press Key 5 once to enter the text.

Industrial Dynamics Company, Ltd. Document 40255-0600

«
...
129
130
131
132
133
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды