Filtec FT-50c Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 239

Filtec FT-50c Скачать руководство пользователя страница 126

Chapter 5: System Software

5-31

# of Container Types

The maximum number of different container types that will be
inspected by this FT-50. The maximum number allowed is deter-
mined by available system memory. The value entered for this
function determines the number of Current Container Types
available.

Current Container Type

A set of stored system parameters for a particular container type.
This function allows you to conﬁgure the FT-50 for a speciﬁc
container and then save the conﬁguration to memory for recall
when switching between container types. When you switch
production between container types, you need only select that
container type from the Current Container Type list, and all
settings are loaded.

The number of container types is determined by the # Of
Container Types function, and the name for each container type is
entered in the Container Text function.

Fill Level

Prepares the FT-50 software for ﬁll level inspection by inserting the
necessary options into the software. When set to Not Present it
removes the options necessary for ﬁll level inspection from the
software.

This function does not activate or deactivate ﬁll level inspection, it
only readies the machine. To turn ﬁll level inspection on or off you
must use the Fill Level Status function.

Underfill Text

Allows you to create a custom name for the Underﬁll Inspection
Option. Any instance in which “Underﬁll” would have appeared
in the software, is replaced by the custom label you created. The
following options are effected:

•

Underﬁll Status

•

Total Underﬁll

•

Reset Underﬁll

•

Alarm Underﬁll

•

Underﬁll Text

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
124
125
126
127
128
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды