Filtec FT-50c Скачать руководство пользователя страница 189

Страница: 189 / 239

FT-50 Fill Level Inspector Service Manual

7-6

The FT-50 Housing

Inspect for damage to metal housing and for wear on the cover
gaskets.

Check to be sure the cover is securely tightened

Clean using a non-caustic nonabrasive soap, water, and a soft
brush. Rinse with clean water.

•

Do not wash with a high pressure nozzle.

•

Do not steam clean

Pressure Regulator and Air Filter

Inspect the polycarbonate sediment bowl for cracks and
abrasion.

Clean and drain the air ﬁlter sediment bowl.

Inspect the air ﬁlter in the inspection head for clogging.

External Wiring

Check the external wiring between the sensors and the FT-50
for damage. Check all connections carefully to be sure they are
not loose.

Check that insulating sleeves are in place.

Replacing the Rejector Pad

The actual lifespan of the rejector pad depends upon the operating
conditions of your production line. Inspect the pad weekly and
replace if worn, cracked, or hardened.

Warning

Turn off all power to your system before attempting any repair
procedure. See

Before You Perform Any Maintenance Procedure

, at

the beginning of this section.

Power down the rejector.

Remove the retaining screw and washer on the top of the
rejector shoe.

Slide the pad up to remove it from the shoe.

Industrial Dynamics Company, Ltd. Document 40255-0600

Содержание FT-50c
















































































































































































































































Результаты поиска

Содержание FT-50c

Отзывы:

Бренды по названию

Популярные бренды

Filtec FT-50c, Сервисное и техническое руководство

Результаты поиска

Содержание FT-50c

Отзывы:

Бренды по названию

Популярные бренды