Filtec FT-50c Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 239

Filtec FT-50c Скачать руководство пользователя страница 129

FT-50 Fill Level Inspector Service Manual

5-34

Bulged End

Prepares the FT-50 software for Bulged End inspection by inserting
the necessary options into the software. When set to Not Present it
removes the options necessary for bulged end inspection from the
software.

This function does not activate or deactivate Bulged End
inspection, it only readies the machine. To turn Bulged End
inspection on or off you must use the Bulged End Status function.

Bulged End Text

Allows you to create a custom name for the Bulged End Option.
Any instance in which “Bulged End” would have appeared in the
software, is replaced by the custom label you created. The
following options are effected:

•

Bulged End Status

•

Total Bulged End

•

Reset Bulged End

•

Alarm Bulged End

•

Bulged End Text

•

Bulged End

Note

This manual assumes the default name for this option. If you
change the default text remember to substitute the new name
when reading this manual. To avoid confusion record the change
in the manual.

To create a name:

1.

Press the Arrow Key until the desired character appears.

2.

Press Key 6 to advance to the next space.

3.

Repeat steps 1 and 2 until you complete the entry and then
press Key 5 once to enter the text.

Industrial Dynamics Company, Ltd. Document 40255-0600

«
...
127
128
129
130
131
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды