manualshive.com logo in svg

Fike CyberCat 1016, Руководство по установке

Поделиться
Скачать
Fike CyberCat 1016 Скачать руководство пользователя страница 58

3.0 SYSTEM COMPONENTS

 

3-38 

CyberCat 254/1016 Installation Manual 

UL S2203 

Rev 14, 09/2015 

P/N: 06-326 

FM  

3.12.2  HAND HELD PROGRAMMER, P/N 10-2648 (NON-LISTED) 

The Hand Held Programmer (See Exhibit 3-78) provides the user the 
ability to 

address

  the Fike CyberCat  addressable devices.    The 

Hand  Held  Programmer  contains the same operating code as the 
CyberCat  and can be used as a training device and/or 
troubleshooting tool. 

Refer to Fike document 06-390, for more information. 

3.12.3  C-LINX SOFTWARE, P/N 06-327 

The C-Linx Software provides a computer interface to the CyberCat 
controller.  It provides the designer the tools to design a system in 
their office and then load the configuration at the project site.  It also 
provides the ability to retrieve, save and print the configuration and 
history of events from the control panel  as well as perform several 
diagnostic functions. 

Refer to Fike document 06-448, for more information. 

3.12.4  INTERFACE CABLE, P/N 10-1874A 

The 10-1874A interface cable (See Exhibit 3-79) consists of a RJ11 
jack, serial cable, and a RJ11 to DB9 connector (wired Fike specific).  
It should be used when connecting the C-Linx Software  to the 
CyberCat using a computer with a DB9 serial (com) port. 

3.12.5  INTERFACE CONVERTER, P/N 02-11139 

The 02-11139 interface converter  (See Exhibit  3-80)  consists of a 
USB-to-DB9 converter only.   This converter is included in the 10-
1874B  interface cable shown  below.    It should be used when 
connecting the C-Linx Software to the CyberCat  using a computer 
with a USB connector instead of a DB9 serial (com) port and would 
connect to the 10-1874A cable for RJ11 connection to the CyberCat 
panel. 

3.12.6  INTERFACE CABLE, P/N 10-1874B 

The 10-1874B interface cable consists of the USB to RS232 (DB9) 
converter (P/N 02-11139) and also includes the 10-1874A  interface 
cable.  It should be used when connecting the C-Linx Software to the 
CyberCat using a computer with a USB connector instead of a DB9 
serial (com) port. 

3.12.7  INTERFACE CABLE, P/N 10-2629 

The 10-2629 interface cable (See Exhibit 3-81) consists of a USB 2.0 
A/B Male-to-Male assembly.  It should be used when programming 
using  the C-Linx Software to 50 point panel  or Handheld 
Programmer. 

Note:

  Requires drivers for proper operation.  Drivers can be 

downloaded from Fike Customer Portal. 

 

Exhibit 3-80:  USB/DB9 

Communication Cable 

 

 

Exhibit 3-78:  Hand Held 

Programmer 

 

Exhibit 3-81: 

USB Communication Cable 

 

Exhibit 3-79:  DB9-RJ11 Cable 

Содержание CyberCat 1016





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды