manualshive.com logo in svg

Fike CyberCat 1016, Руководство по установке

Поделиться
Скачать
Fike CyberCat 1016 Скачать руководство пользователя страница 39

 

 

3.0 SYSTEM COMPONENTS 

 

UL S2203 

CyberCat 254/1016 Installation Manual 

3-19 

FM 

 

P/N: 06-326 

Rev 14, 09/2015

 

3.6 

PERIHERAL BUS DEVICES 

Several optional components can be installed on the CyberCat controller’s RS485 peripheral bus (31 devices 
maximum)  to  provide remote annunciation and control of system events,  and to expand  the systems 
operational capabilities.  A brief description of each component and its functionality is provided in this section 
for reference purposes.  For a complete description of each module’s functionality, installation and wiring, 
refer to the referenced installation sheet/manual. 

3.6.1 

FOURTEEN BUTTON REMOTE DISPLAY UNIT, P/N 10-2646 

The Fourteen Button Remote Display Unit (See Exhibit 3-30) 
provides a 4x20 character LCD that mimics the host control 
panel’s display.  This allows system status information to be 
displayed at a remote location.  The unit is equipped with 
eight programmable buttons that can be used to perform 
system control functions such as Reset, Silence, 
Acknowledge, etc.  Switch functions are protected by the 
unit’s integral security access key.  In addition, the RDU is 
equipped with an internal piezo and five status LEDs that 
provide instant audible and visual notification of system 
status changes. 

Refer to Fike document 06-610, for more information. 

Note:

  This unit can only be used on systems with 

panel firmware V3.0 or higher. 

3.6.2 

TEN BUTTON REMOTE DISPLAY UNIT, P/N 10-2631 

The Ten Button Remote Display Unit (See Exhibit 3-31) provides 
a 4x20 character LCD that mimics the host control panel’s 
display.  This allows system status information to be displayed at 
a remote location.  The unit is equipped with four control 
switches that allow initiation of system Drill, Acknowledge, 
Silence and Reset functions from the unit.  Switch functions are 
protected by the unit’s integral security access key.  In addition, 
the RDU is equipped with an internal piezo and five status LEDs 
that provide instant audible and visual notification of system 
status changes. 

Refer to Fike document 06-610, for more information. 

Note:

  This unit can only be used on systems with panel 

firmware V3.0 or higher. 

 

Exhibit 3-30:  Fourteen Button 

Remote Display Unit 

 

Exhibit 3-31:  Ten Button 

Remote Display Unit 

 

Содержание CyberCat 1016





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды