FIEDLER H1 Скачать руководство пользователя | Manualshive

Страница: 38 / 82

background image

Hydro Logger H1

User manual

38

electronics for ecology

FIEDLER

BASIC INFORMATION WINDOW

The basic information window is displayed first, which includes the current date
and time set in the instrument, the status of the power battery, the temperature
inside the instrument and, if applicable, the relative humidity value in the in-
strument.
The date and time are automatically compared when communicating with the
server if they differ by more than 30 sec.
The temperature inside the instrument is only informative, as is the relative hu-
midity. Elevated relative humidity is dangerous for the life of the electronic cir-
cuitry and indicates a leak in the instrument. If the humidity exceeds 80%, check
the tightness of the cable glands and the metal cover of the instrument itself.

Basic information window

The battery symbol on the left edge is accompanied by a vertical bar showing
the battery status (remaining capacity). This value is calculated from the diffe-
rence in voltage between the loaded and unloaded supply battery.

CYCLIC IMAGING

The basic information window is replaced by individual windows containing one
measuring channel each after the preset time (3 sec.). The analogue channels
(Channels-A) are displayed first, followed by the binary channels (Channels-B).
The  meaning  and  settings  of  the  individual  measurement  channels  will  be
described in detail in chapter 6.4 on page 46.
Displaying the last set channel will automatically end the display cycle, turn off
the display and the HydroLogger H1 will enter power saving mode, which is its
normal operating state.
If the user presses the communicator button briefly (1 sec) at any time during
the display, the display cycle will be executed 3 times in total and only then the
display will be switched off and enter the power saving mode.

ANALOG CHANNEL DISPLAY

The following figure represents the analog channel window C1 (Channel 1).
Channel 1 is usually set up to record the flow from a connected flow meter.
If the HydroLogger detects an error in the input measured signal, the display will
show an error code with an E instead of the current measured flow value (shown
in Figure E10). The bottom line of the display shows the total flow volume. Such
an error can be a current less than 4 mA or greater than 20 mA flowing from a
sensor with a 4-20 mA output signal or a broken cable for sensors communica-
ting over the RS485 serial interface.

D a t e a n d t i m e

Te m p e r a t u r e a n d

r e l a t i v e h u m i d i t y

B a t t e r y s t a t u s

E n d o f c y c l i c

d i s p l a y

E x t e n d i n g t h e
i m a g i n g c y c l e

«
...
36
37
38
39
40
...
»

Содержание H1



















































































Отзывы:

Нет отзывов

Похожие инструкции для H1

Бренд: M-system Страницы: 4

Бренд: Metal Samples Company Страницы: 54

Бренд: 3M Страницы: 15

Бренд: Turner Страницы: 33

Бренд: YDOC Страницы: 134

Бренд: JERICHO Страницы: 16

Бренд: Omega Страницы: 6

Бренд: Eagle Tree Systems Страницы: 17

Бренд: Lascar Electronics Страницы: 4

Бренд: Agilent Technologies Страницы: 273

TELEMAC SMARTEC NOVA METRIX MB-3TL

Бренд: ROCTEST Страницы: 14

Бренд: keyto Страницы: 4

Бренд: Honeywell Страницы: 11

Бренд: VOLTCRAFT Страницы: 156

ThermaData 4-Channel Logger

Бренд: ThermoWorks Страницы: 2

Бренд: ELPRO Страницы: 28

Бренд: TQC Страницы: 16

Бренд: Signatrol Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды