FIEDLER H1 Скачать руководство пользователя | Manualshive

Страница: 27 / 82

background image

Hydro Logger H1

User manual

FIEDLER

electronics for ecology

27

ANTENNA INSTALLATION

When installing the antenna, the current GSM signal strength at the antenna
installation site can be displayed on the unit's display to optimize the final an-
tenna placement.

PROCEDURE FOR DETECTING THE GSM FIELD STRENGTH:

•

Connect the GSM antenna to the device and place it in the expected
location of the highest GSM field strength.

•

Press the button briefly to switch on the device. The following long press
(3 sec - until beep) will command the HydroLogger to try to log into the
GSM network. If there is at least the minimum GSM field strength at the
antenna location, the instrument will log into the GSM network after
approx. 20 sec. and the display will show the name of the operator and
the measured GSM field strength will be shown in ticks in the right part
of the display above the schematic mark of the antenna. The numerical
expression of the GSM field strength can be found in the upper right
corner of the display in the form Q=...

•

Manipulate the antenna to achieve a GSM field strength of at least Q = 8
or higher. The measured Q value is refreshed at an interval of about 5
seconds.

•

To  extend  the  display  on  time,  press  the  button  briefly  again  before
exiting the recalled mode. By default, the device is set so that the display
backlight  turns  off  after  1  minute  from  the  last  button  press  and  the
selected  mode  after  another  minute.  Therefore,  if  you  press  the
instrument  button  briefly  at  an  interval  of  less  than  1  minute,  the
instrument's backlit display will continuously show the measured GSM
field  strength.  Any  long  press  of  the  button  (>=3  sec)  will  trigger  the
archived data to be sent via GPRS communication to the database server.

•

After finding the maximum possible GSM field strength (the highest Q
value), leave the instrument at rest. Two minutes after the last button
press, the display will gradually show the set measurement channels and
then the instrument will switch off - the instrument will enter its normal
operating mode.

TREATMENT OF THE GSM CONNECTOR AGAINST MOISTURE

The used GSM connector type FME does not contain a
seal to  prevent  moisture from  entering  the  connector
and  therefore  it  is  necessary  to  treat  this  connector
when installing the station in a humid environment. The
easiest  way  to  do  this  is  to  wrap  the  joint  with  self-
vulcanizing insulating tape (in a pinch, ordinary electri-
cian's insulating tape.

«
...
25
26
27
28
29
...
»

Содержание H1



















































































Отзывы:

Нет отзывов

Похожие инструкции для H1

Бренд: Nivus Страницы: 60

Бренд: X2E Страницы: 192

Бренд: Escort Страницы: 28

Бренд: MadgeTech Страницы: 10

Бренд: MadgeTech Страницы: 12

Бренд: MadgeTech Страницы: 16

Бренд: MadgeTech Страницы: 4

Бренд: Rand McNally Страницы: 7

Бренд: Ranger Страницы: 27

WineCap WSD12T-IIDR

Бренд: Capetti Elettronica Страницы: 9

Бренд: Chauvin Arnoux Страницы: 32

Бренд: Chauvin Arnoux Страницы: 38

Бренд: Chauvin Arnoux Страницы: 64

Бренд: EchoStar Страницы: 58

Бренд: Dataq Страницы: 84

Бренд: V-Sun Страницы: 8

Бренд: Kipp & Zonen Страницы: 53

Бренд: Extech Instruments Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды