manualshive.com logo in svg

FibroLAN Falcon Gen-3 M-Class, Руководство пользователя

Поделиться
Скачать
FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 94

Falcon 

M-Class

  |  User Guide 

 

94 

 

Table 4-45: QoS Ingress Port Classification parameters  

QoS Ingress Port Classification 

Port 

The port number for which the configuration below applies.

 

Cos  

Controls the default class of service. 
All frames are classified to a CoS. 

There is a one to one mapping between CoS, queue and priority. 
A CoS of 0zero)

 

has the lowest priority 

If the port is VLAN aware, the frame is tagged and Tag Class. is enabled, 
then the frame is classified to a CoS that is mapped from the PCP and DEI value in the 

tag. Otherwise the frame is classified to the default CoS. 
The classified CoS can be overruled by a QCL entry 
Note: If the default CoS has been dynamically changed, then the actual default CoS is 

shown in parentheses after the configured default CoS.

 

DPL 

Controls the default 

Drop Precedence Level

  

All frames are classified to a drop precedence level. 

If the port is VLAN aware, the frame is tagged and Tag Class. is enabled, 
then the frame is classified to a DPL that is mapped from the PCP and DEI value in the 

tag. Otherwise the frame is classified to the default DPL. 
The classified DPL can be overruled by a QCL entry 

PCP 

Controls the default PCP (

P

riority 

C

ode 

P

oint) 

All frames are classified to a PCP entry 
If the port is VLAN aware and the frame is tagged, then the frame is classified to the 
PCP value in the tag Otherwise the frame is classified to the default PCP value. 

DEI 

Controls the default 

DEI

 for untagged frames. 

All frames are classified to a DEI value 
If the port is VLAN aware and the frame is tagged, then the frame is classified to the 
DEI value in the tag Otherwise the frame is classified to the default DEI value. 

Tag Class. 

Shows the classification mode for tagged frames on this port. 
 

Disabled

:

 Use default QoS class and DP level for tagged frames. 

 

Enabled

:

 Use mapped versions of PCP and DEI for tagged frames. 

Click on the mode in order to configure the mode and/or mapping. 
Note: This setting has no effect if the port is VLAN unaware. 
Tagged frames received on VLAN unaware ports are always classified to the default 
CoS and DPL. 

DSCP Based 

Click to Enable DSCP Based QoS Ingress Port Classification. 

Address 

Mode 

The IP/MAC address mode specifying whether the 

QCL

 classification must be based 

on source (SMAC/SIP) or destination (DMAC/DIP) addresses on this port The allowed 
values are: 
Source: Enable SMAC/SIP matching. 
 
Destination

:

 Enable DMAC/DIP matching 

Buttons 

Save: 

Click to save changes.

 

Reset:

 

Click to undo any changes made locally and revert to previously saved values 

 

 

 

Содержание Falcon Gen-3 M-Class


























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды