FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 416 | Manualshive

Страница: 416 / 473

FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 416

Falcon

M-Class

| User Guide

416

Figure

4

-40: Rmon Statistics Status Overview

Table 5-36: Rmon Statistics Status Overview Parameters

RMON Statistics Status Overview

ID

Indicates the index of History control entry.

Data Source

(ifIndexif (Index)

The port ID which has to be monitored.

Drop

The value of sysUpTime at the start of the interval over which this sample was
measured.

Octets

The total number of events in which packets were dropped by the probe due to lack of
resources.

Pkts

The total number of packets (including bad packets, broadcast packets, and multicast packets)
received.

Broadcast

The total number of good packets received that were directed to the broadcast address.

Multicast

The total number of good packets received that were directed to the multicastaddress.

CEC Errors

The total number of packets received that had a length (excluding framing bits, but including

FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad Frame Check
Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral

number of octets (Alignment Error)

Under size

The total number of packets received that were less than 64 octets.

Over size

The total number of packets received that were longer than 1518 octets.

Frag.

The number of frames which size is less than 64 octets received with invalid CRC.

Jabb.

The number of frames which size is larger than 64 octets received with invalid CRC.

Coll.

The total number of octets of data (including those in bad packets) received on the
network.

64

The total number of packets (including bad packets) received that were 64 octets in length.

65~127

The total number of packets (including bad packets) received that were between 65 to 127
octets in length.

128~255

The total number of packets

(including bad packets) received that were between 128 to 255

octets in length.

256~511

The total number

of packets (including bad packets) received that were between 256 to 511

octets in length.

512~1023

The total number

of packets (including bad packets) received that were between 512 to 1023

octets in length.

1024~1588

The total number

of packets (including bad packets) received that were between

1024 to 1588 octets in length

Buttons

Auto-refresh

: Check this box to refresh the page automatically. Automatic refresh occurs

every 3 seconds

Refresh:

Click to refresh the page immediately.

<<

: Updates the the table starting from the first entry in the Alarm Table, i.e. the

entry with the lowest ID.

>>:

Updates the table, starting with the entry after the last entry currently displayed.

«
...
414
415
416
417
418
...
»

Содержание Falcon Gen-3 M-Class


























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды