FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 338 | Manualshive

Страница: 338 / 473

FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 338

Falcon

M-Class

| User Guide

338

Dual ended LM

This method is a proactive tool to measure the frame loss. MEPs use CCM messages to deliver the
information on number of service frames transmitted and received.
Each MEP measures Near-end loss and Far-end loss based on the counters contained in CCM
message from its peer and the local counters.

It should be noted that measurement of frame loss based on service frames applies only to point-
to-point service.

The various mentioned parameters are reported in the below displays and related tables.

Figure 4-198: Loss Measurement Displays

Table 4-174

:

Loss Measurement Parameters

Loss Measurement

Enable

Loss Measurement based on transmitting/receiving CCM or LMM/LMR PDU
can be enabled/disabled - see 'Ended'. This is only valid with one Peer

MEP configured.

CCM

is an acronym for

C

ontinuity

C

heck

M

essage. It is a OAM frame

transmitted from a MEP to it's peer MEP and used to implement CC
functionality.

Priority

The priority to be inserted as PCP bits in TAG (if any). In case of enable of

Continuity Check and Loss Measurement both implemented on SW based
CCM, 'Priority' has to be the same.

Frame

Rate

Selecting the frame rate of CCM/LMM PDU. This is the inverse of

transmission period as described in Y.1731. Selecting 300f/sec or 100f/sec
is not valid. In case of enable of Continuity Check and Loss Measurement
both implemented on SW based CCM, 'Frame Rate' has to be the same.

Cast

Selection of CCM or LMM PDU transmitted unicast or multicast. The
unicast MAC will be taken from the 'Unicast Peer MAC' configuration. In

case of enable of Continuity Check and dual ended Loss Measurement
both implemented on SW based CCM, 'Cast' has to be the same.

Ended

Single:

Single ended Loss Measurement implemented on LMM/LMR.

Dual:

Dual ended Loss Measurement implemented on SW based CCM

FLR

Interval

This is the interval in seconds where the FLR (Frame Loss Ratio ) is

calculated.

Loss Measurement State

Near End Loss

Count

The accumulated near end frame loss count - since last
'clear'.

Far End Loss Count

The accumulated far end frame loss count - since last 'clear'.

«
...
336
337
338
339
340
...
»

Содержание Falcon Gen-3 M-Class


























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды