FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 219 | Manualshive

Страница: 219 / 473

FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 219

Falcon

M-Class

| User Guide

219

4.15.1

PTP External Clock Mode

This section allows the user to configure the PTP External clock mode settings

Figure 4-122: PTP External Clock Mode

Table 4-118: PTP External Clock Configuration Parameters

PTP External Clock Configuration

One_pps_mode

This Selection box will allow you to select the One_pps_mode
configuration.

The following values are possible:
1. Output : Enable the 1 pps clock output

2. Input: Enable the 1 pps clock input
3. Disable : Disable the 1 pps clock in/out-put

External Enable

This Selection box will allow you to configure the External clock output.

The following values are possible:
1. True : Enable the external clock output

2. False : Disable the external clock output

Adjust Method

This Selection box will allow you to configure the Frequency adjustment
configuration.

1

. LTC frequency

: Select Local Time Counter (LTC) frequency control

2.

SyncE-DPLL

: Select SyncE DPLL frequency control, if allowed by

SyncE
3

. Oscillator

: Select an oscillator independent of SyncE for frequency

control, if supported by the HW

4. .

LTC phase

: Select Local Time Counter (LTC) phase control

(assumes that the frequency is locked by means of SyncE

Clock

Frequency

This will allow setting the Clock Frequency.
The possible range of values are 1 - 25000000 (1 - 25MHz)

Buttons

Save

: Click to save changes.

Reset

: Click to undo any changes made locally and revert to previously

saved values.

PTP Monitor

: click on it to go to: PTP Monitor display

Sync center config

: click on it to go to Sync Center config display

One PPS (1PPS) mode of operation.

Network systems require synchronizing with a 1Hz or 1PPS input clock signal.
Such timing signal may also derive from a GPS receiver.
This signal is needed to perform phase synchronization between Master and slave devices

«
...
217
218
219
220
221
...
»

Содержание Falcon Gen-3 M-Class


























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды