Ferno POWER X SN-POW1001, Руководство пользователя

Страница: 45 / 50

FERNO/MAN/0721/216-R22/UK
45
10 - MAINTENANCE
10.1 - Maintenance Schedule
The trolley requires regular maintenance. Set up and follow
a maintenance schedule. The table at right/below represents
minimum intervals for maintenance. Keep maintenance records.
A sample maintenance record sheet is provided at the end of this
manual.
When using maintenance products, follow the manufacturers’
directions and read the manufacturers’ material safety data sheets.
You can purchase a recommended disinfectant from your Ferno
distributor or Ferno UK Service Department.
IMPORTANT
Disinfectants and cleaners containing chlorine/bleach,
phenol, or iodine can cause damage. It is recommended not
to use products containing these chemicals. If these type of
disinfectants are to be used, then to minimise the level of
damage they will cause it is recommended that they are used
with the least possible contact time, diluted as specified by
the manufacturer’s guidelines, and that the equipment is
then thoroughly washed down with water after disinfecting
in order to remove any chemical residue and prevent any
ongoing surface damage from occurring. Accessories such as
push poles, IV poles etc. should be cleaned and disinfected
whilst detached from the trolley and the fixing points on the
trolley disinfected and thoroughly washed down after.
Maintenance
10.2 - Cleaning the Trolley
Regular cleaning helps reduce the risk of transmitting disease and
enables equipment to function at its optimum.
Ensure that all equipment is removed from the trolley and that
the Olson Power distribution socket is disconnected from mains
supply
Trolley should be hand-wiped using a suitable cleaning solution.
For particularly grimy cases, especially if the trolley has been in
storage for a long period, it may be necessary to first clean the
trolley with a water-soluble solvent-soaked cloth.
Once cleaned, dry the trolley with a soft towel, paying particular
attention to swivel and sliding joints. If a compressed air hose is
available, you may find that compressed air jets are more effective
in drying the hard-to-reach places..
Ensure no liquid enters the control box, battery holder
power connectors or any other electrical component.
10.3 - Disinfecting the Trolley
Wipe all surfaces with disinfectant. Follow the disinfectant
manufacturer’s instructions for application method and contact
time. Ferno recommends you inspect the trolley for damage as
you clean and disinfect it. See note regarding disinfectants to use.
1. Remove the mattress, patient harness, straps and any accessories.
2. Hand clean all surfaces of the trolley with warm water and a mild
detergent.
3. Rinse with warm, clear water. Dry the trolley with a towel and
allow it to air-dry thoroughly, replacing the mattress and
harness/straps prior to storage.
4. To disinfect: Apply disinfectant to the trolley, following the
disinfectant manufacturer’s instructions for application method
and contact time. Ensure to wash down thoroughly after
disinfecting to remove any chemical residue that might cause
long-term damage
10.4 - Disinfecting & Cleaning Harness
It is recommended to remove the harness, straps and mattress
from the trolley before cleaning and disinfecting to ensure they
can be cleaned effectively on all surfaces.
Cleaning Webbing straps
1. Immerse webbing straps in a solution of mild soap and water to
clean Do not immerse any metal buckles or metal fixation clips in
the solution, these should be wiped clean only.
2. Repeatedly dip the webbing in clean water to rinse. Do not
immerse any metal buckles or fixation clips. Hang the straps to
air-dry. Attach only clean, dry straps back onto to the equipment.
Disinfecting webbing straps
1. Immerse or spray the webbing straps following the selected
disinfectant manufacturer’s instructions for application method
and contact time. Do not immerse any metal buckles or metal
fixation clips into disinfectant liquid
2. Spray the metal buckles and fixation clips with disinfectant
cleaner spray, following the disinfectant manufacturer’s
instructions for application method and contact time
3. Hang the straps to air-dry if needed. Attach only dried straps to
the equipment
Cleaning Biosafe straps
1. Wipe-clean the straps, buckles and fixing clips with mild soap
and water
2. Hang the straps to air-dry. Attach only clean, dry straps back
onto to the equipment
Disinfecting Biosafe straps
1. Spray the webbing straps, metal buckles and fixation clips
with disinfectant cleaner spray, following the disinfectant
manufacturer’s instructions for application method and contact
time
2. Hang the straps to air-dry if needed. Attach only dried straps to
the equipment
WARNING
Improper maintenance can cause injury. Maintain the
trolley only as described in this manual.
Minimum
Maintenance Intervals
Each U
se
A
s N
eeded
Each M
on
th
Disinfecting
•
Cleaning
•
Inspecting
• •
Lubricating
•