Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 75

Страница: 75 / 222

Pos.

Designation

Note

not used

Push button for rear windscreen

wiper

Interval/on/off

Push button for rear windscreen

wiper

Push button for rear windscreen

heating

The rear windscreen heating is

shut down after three minutes.

Push button for rear working

lights

Push button for inside cabin light

Push button for front working

lights

Push button for flashing beacon

Push button for front windscreen

washer

Push button for front windscreen

wiper

Interval/on/off

4.2.2

Heating / air conditioning

4.2.2.1

Rotary switch for air distribution

Position "Top"

Air flow to windscreen

Position

"Middle"

Air flow to body

Position

"Bottom"

Air flow to body and footwell

Fig. 30

Display and control elements – Cabin

BW 213 D-5

Содержание BOMAG BW 213 D-5































































































































































































































Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию, Страница: 75 / 222

Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы: