Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 159

Страница: 159 / 222

Protective equip-

ment:

Working clothes

Protective gloves

Park the machine in secured condition

Chapter 6.7 „Park the machine in

secured condition.“ on page 115

Clean the area around the level inspection

plug (1) and unscrew the plug.

The oil level must reach the bottom

edge of the level bore.

A second inspection plug is

located on the left front side

of the drive axle.

If necessary clean the area around the filler

plug (2) and unscrew the filler plug.

Fill in oil through the filler bore, until it starts

to run out through the level inspection bore.

After filling in oil wait until the oil has evenly

distributed inside the axle.

Retighten level inspection and filler plugs.

8.7.4

Checking the oil level in the wheel hubs

NOTICE!
Components may get damaged!

– Use only gear oil of the permitted

specification

Chapter 8.3.6

„Gear oil SAE

80W-140“ on page 147

Fig. 114

Maintenance – Every 250 operating hours

BW 213 D-5

159

Содержание BOMAG BW 213 D-5































































































































































































































Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию

Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды