manualshive.com logo in svg

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию

Поделиться
Скачать
Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 11

You should only operate the machine in compli-

ance with these instructions.
Strictly observe the safety regulations.
If you are not yet acquainted with the controls

and indicating elements on this machine, you

should thoroughly read the corresponding

chapter

 

Ä

 Chapter 4 „Display and control ele-

ments“ on page 63

.

The description of the individual operating

steps including the notes on safety to be fol-

lowed can be found in chapter "Operation"

Ä

 Chapter 6 „Operation“ on page 95

.

Thorough maintenance of the machine guaran-

tees far longer safe functioning of the machine

and prolongs the lifetime of important compo-

nents. The effort required for this purpose is by

all means lower than the faults that may occur

in case of non-compliance.
The machine must only be serviced by quali-

fied and authorized personnel. A description of

all necessary service work as well as informa-

tion on fuels and lubricants can be found in the

chapter "Maintenance"

 

Ä

 Chapter 8 „Mainte-

nance“ on page 133

.

For your own personal safety you should only

use original parts from BOMAG.
For your machine we offer original parts kits to

make maintenance easier.
In the course of technical development we

reserve the right for technical modifications

without prior notification.
These operating and maintenance instructions

are also available in other languages.
Apart from that, you can also order the spare

parts catalogue against the serial number of

your machine.

Introduction – Foreword

 

BW 213 D-5

 

11

Содержание BOMAG BW 213 D-5































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды