manualshive.com logo in svg

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию

Поделиться
Скачать
Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 130

7.4 

Loading by crane

Loads must only be attached and hoisted by an

expert / capable person.
Do not use damaged or in any other way

impaired lashing points.
Use only lifting gear and lifting tackle with suffi-

cient load bearing capacity for the weight to be

loaded. Minimum load bearing capacity of

lifting gear: see max. operating weight

Ä

 Chapter 2 „Technical data“ on page 15

.

Always use appropriate lifting and lashing

means on the lifting and lashing points.
Use lifting and lashing gear only in the pre-

scribed direction of load application.
Lifting and lashing gear must not be damaged

by machine components.
When lifting the machine avoid uncontrolled

movements of the load. If necessary, hold the

load with guide ropes.

1.

Shut down the engine.

2.

Engage the articulation lock

 

Ä

 Chapter

8.2.2.1 „Engaging the articulation

lock“ on page 137

.

3.

Fasten the lashing tackle at the marked

lifting points.

4.

Adjust the length of the lifting tackle in such

a way, that the crane hook is vertically

above the centre of gravity of the machine.

5.

Use a suitable cross-beam to prevent the

machine from being damaged.

Fig.  97

Loading/transporting the machine – Loading by crane

 

BW 213 D-5

 

130

Содержание BOMAG BW 213 D-5































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды