Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 104

Страница: 104 / 222

6.5

Working with vibration

6.5.1

Preliminary remarks and safety notes

NOTICE!
Possible damage to neigh-

bouring buildings!

– When compacting with vibration

you must always check the effect

of the vibration on nearby build-

ings and underground supply

lines (gas, water, sewage, elec-

tric power).

– If necessary stop compacting

with vibration.

NOTICE!
Components may get damaged!

– Do not activate the vibration on

hard (frozen, concrete) ground.

Vibration at standstill causes transverse marks

Switch the vibration on only after shifting the

travel lever to the desired travel direction.

Switch the vibration off before stopping the

machine.

Operation – Working with vibration

BW 213 D-5

104

Содержание BOMAG BW 213 D-5































































































































































































































Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию

Результаты поиска

Содержание BOMAG BW 213 D-5

Отзывы:

Бренды по названию

Популярные бренды