manualshive.com logo in svg

Fayat Group BOMAG BW 213 D-5, Инструкция по эксплуатации, Инструкция по обслуживанию

Поделиться
Скачать
Fayat Group BOMAG BW 213 D-5 Скачать руководство пользователя страница 46

3.6.2 

Starting the engine

The machine must only be started and oper-

ated from the driver’s seat.
Before starting and moving the machine make

sure that there are no persons inside the

danger zone.
For starting set all control levers to "neutral

position".
Do not use any starting aids like start pilot or

ether.
The machine must not be operated with dam-

aged, missing or non-functional safety installa-

tions.
After starting check all display instruments.
Do not inhale exhaust fumes, because they

contain toxic substances, which could cause

damage to health, unconsciousness or even

death.
For operation in closed or partly closed rooms

ensure adequate ventilation.

3.6.3 

Starting the engine with jump leads

Connect positive with positive and negative

with negative (ground cable) – always connect

the ground strap last and disconnect it first! A

wrong connection will cause severe damage in

the electric system.
Do not start the engine by shorting the electric

terminals on the starter motor, because the

machine may start to drive immediately.

Concerning your safety – Start-up procedure

 

BW 213 D-5

 

46

Содержание BOMAG BW 213 D-5































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды