FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 9

Страница: 9 / 31

Revision date: 01.14.21

112525

Assembly Instructions

1. Using the assembled frame as a bench, place one 8'

channel (116211L096) on the cross supports.

2. Using the 112509 adhesive, attach the plain end cap (no

outlet–116214) to the end of the channel that is resting

on the high side of the support table. This is the end with

the 36" legs. Be sure to coat the end of the channel with

adhesive

before

you install the end cap. Repeat for all 8'

channels.

3. Move to the other end of the channel and install the 116215

end cap (with outlet). Coat the end of the channel with

adhesive

before

you install the end cap. Repeat for all

channels.

4. Next, attach a 90° elbow (WF6682) to each 116215 end

cap as shown. Apply pvc primer and pvc cement to end cap

outlet and inside of fittin, and slide fitting onto outlet. Install

fitting as shown with open end pointing down in the 6:00

o'clock position.

ATTENTION:

Verify that you are using the WF6682 elbows.

These are without threads.

Do not use the WF6692 elbow.

ASSEMBLE ALL 8' 116211L096 CHANNELS

5. Once all end caps and drain elbows are in place, carefully

flip all channels over so the bottom is facing up and the open

top is down.

6. Apply the 112509 adhesive along the edges to secure end

caps to each 8' channel. Photos show an end cap with an

outlet. Secure the plain end caps in the same manner.

NOTE:

Be sure to coat all edges and seams of the end caps

to prevent leaks.

7. Allow the adhesive to dry before moving the channels or

testing the system.

8. Continue by assembling and attaching the 2" pvc drain tube.

Apply primer and cement in a well-ventilated area.

Read container information for additional precautions.

WF6682

Elbow

NFT Channel (8')

WF6682

Elbow

open

top-inside

channel

bottom

PVC Primer

PVC

Cement

Содержание Growers Supply HydroCycle 4" Pro NFT
































Результаты поиска

Содержание Growers Supply HydroCycle 4" Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренды по названию

Популярные бренды

FarmTek Growers Supply HydroCycle 4" Pro NFT, Руководство пользователя

Результаты поиска

Содержание Growers Supply HydroCycle 4" Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренды по названию

Популярные бренды