FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 31

background image

15

Revision date: 01.14.21

112525

Complete these steps:
1. Cut a 28" piece of 3/4" pvc tube from a 10' section of WF4130 supplied with the system.
2. Slide a WF1530 elbow onto one end of the 28" pipe and a WF2990 cap onto the other end.

Do

not cement at this time.

8

Assembly Instructions

ASSEMBLE NUTRIENT SUPPLY MANIFOLD AND ATTACH TO FRAME

3. Move to the frame and snap the supply manifold into the 3/4" hangers. Install so elbow is at the

corner opposite the tee fitting of the drain manifold at the opposite end of the frame.

WF2990

WF1530

4. Verify the open end of the elbow points towards the opposite end of the frame and mark elbow

location on both the elbow and manifold tube for alignment purposes.

5. Continue with the next procedure.

TOP VIEW

DIAGRAM

(not to scale)

Elbow installed at

corner opposite the

tee fitting of the drain

manifold.

Mark for alignment.

«
...
13
14
15
16
17
...
»

Содержание Growers Supply HydroCycle 4" Pro NFT
































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренд: Parata Страницы: 40

Бренд: Cadex Страницы: 300

Бренд: HABYS Страницы: 16

Бренд: Tascam Страницы: 8

Бренд: Palmako Страницы: 83

Бренд: Mach Страницы: 12

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Бренд: Nady Audio Страницы: 2

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренд: Labconco Страницы: 174

Бренд: Fri-Jado Страницы: 48

Бренд: Janschitz Страницы: 40

Бренд: Dangerous power Страницы: 38

Бренд: ABS Страницы: 17

Бренд: American DJ Страницы: 8

Sure Stripe 3650

Бренд: AIRLESSCO Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды