FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 31

background image

7

Revision date: 01.14.21

112525

End

End

Assembly Instructions

6. With assistance, arrange and stand the two (2) base assemblies so that the leg lengths

of each base assembly are aligned (i.e., 36" with 36", 34 3/4" with 34 3/4", and so on).

NOTE:

It is best to

construct the support frame in the area where it will be used

so

the frame can be leveled for final assembly.

7. Next, take one 131P043 pipe and slide it through the tee fittings at one end of each base

assembly. Repeat the step to install the center 43" cross support and remaining end

support.

8. Set the width of the support frame at ground level and at the cross support . See the

diagram below and in the Quick Start section near the back of this guide.

9. Tighten all set screws to secure all connections.
10. Continue with the next procedure.

1

ASSEMBLE MAIN SUPPORT FRAME (continued)

Ground Level

Leg

43" Cross Support

(131P043)

End View of Support Frame

38"

Center-to-Center

38"

Center-to-Center

«
...
5
6
7
8
9
...
»

Содержание Growers Supply HydroCycle 4" Pro NFT
































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: Panasonic Страницы: 9

Бренд: Yardistry Страницы: 9

Бренд: Cadex Страницы: 300

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Gainsborough Страницы: 2

Бренд: Gainsborough Страницы: 2

Бренд: Gait up Страницы: 12

Бренд: Gait up Страницы: 6

Бренд: Gaiam Страницы: 2

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: tayco Страницы: 111

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды