FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 2

Страница: 2 / 31

112525

Revision date: 01.14.21

REQUIRED TOOLS

The following list identifies the main tools needed to

assemble the hydroponic system. Additional tools may

be needed.
• Tape measure and marker
• Variable speed drill (cordless with extra batteries

works best)

•  1/4" hex key (Allen) wrench
•  Saw for metal and PVC
•  Hammer and gloves
•  Level (2'-3'– recommended)
•  Adjustable pliers
•  5/16" drill bit and 1", 1-3/8", and 2-1/2" hole saws

READ THIS DOCUMENT BEFORE YOU BEGIN

Thank you for purchasing the HydroCycle Pro NFT hydroponic lettuce system. When properly assembled and maintained, this product will provide years of

reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the system. Please read

these instructions

before

you begin. If you have any questions during the assembly, contact Customer Service at 1.800.245.9881 for assistance.

ASSEMBLY PROCEDURE

Following the instructions as presented will help

ensure the proper assembly of your hydroponic table.

This manual describes how to assemble a single

table that includes four (4) eight foot (8') channels.

The steps outlining the assembly process are as

follows:
1. Verify that all parts are included in the shipment.

Notify customer service for questions or

concerns.

2. Read these instructions and all additional

documentation included with the shipment

before

you begin.

3.  Gather the tools and assistants.
4.  Assemble the NFT frame and system.
5.  Read the care and maintenance information.

CARE AND MAINTENANCE

Proper care and maintenance of your

hydroponic table is important. Check the

following items periodically to properly

maintain your hydroponic table.
• Check connections and all fasteners to

verify that they remain tight.

• Do not climb or stand on the frame or

channels at anytime.

• Verify that the supply lines and related

fittings are clean and functioning properly.

• Replace all worn or damaged parts and

fittings promptly.

• Repair all leaks immediately.
• If the table is moved, inspect all parts and

connections before reassembling and use.

• For replacement or missing parts, call

1.800.245.9881 for assistance.

Important Information

SAFETY PRECAUTIONS

•  Wear eye protection.
•  Wear gloves when handling metal pipes.
•  Use a portable GFCI (Ground Fault Circuit

Interrupter) when working with power tools and

cords.

QUICK START GUIDE

For a quick overview of this product, its

components, and connection details consult

the Quick Start Guide at the back of these

instructions.

WARNING:

KEEP ALL ELECTRICAL

CORDS AND CONNECTIONS OUT OF THE

RESERVOIR. CONSULT THE SERVICES

OF A QUALIFIED ELECTRICIAN TO

ADEQUATELY AND SAFELY CONNECT THE

PUMP TO A POWER SUPPLY.

ALL ELECTRICAL CIRCUITS SHALL BE

DESIGNED IN ACCORDANCE WITH LOCAL

AND REGIONAL BUILDING CODES AND

STANDARDS.

Содержание Growers Supply HydroCycle 4" Pro NFT
































Результаты поиска

Содержание Growers Supply HydroCycle 4" Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренды по названию

Популярные бренды

FarmTek Growers Supply HydroCycle 4" Pro NFT, Руководство пользователя

Результаты поиска

Содержание Growers Supply HydroCycle 4" Pro NFT

Отзывы:

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренды по названию

Популярные бренды