FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 31

background image

17

Revision date: 01.14.21

112525

1. Once all gromets are installed, apply pvc primer and cement to each end of the pvc supply manifold and inside elbow and

cap and reinstall. Be sure to align the marks to install the elbow in the correct position.

FINISH MANIFOLD

10

Assembly Instructions

Apply primer and cement to both ends of the supply

manifold and inside fittings. Reinstall fittings.

WF6990 PVC

Cement & 113372

PVC Purple Primer

2. Allow cement to set and snap the assembled manifold back in the hangers.

IMPORTANT:

Assemble manifold by positioning top hat grommets down toward floor. Review sample picture below for a finished manifold with 1/4" feeder

tubes to NFT channels.

3. Continue with the next procedure.

Supply Manifold Installed

Cement

Cement

ATTENTION:

Actual system may differ.

«
...
15
16
17
18
19
...
»

Содержание Growers Supply HydroCycle 4" Pro NFT
































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

Бренд: Gardena Страницы: 13

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Zenbooth Страницы: 60

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: ACDC Страницы: 4

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: Rapid Technic Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды