FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 31

background image

19

Revision date: 01.14.21

112525

ASSEMBLE PUMP AND MAIN SUPPLY LINE

12

Assembly Instructions

110722

Utility Pump

Using the photos on this page and the notes that follow,

install the water pump and main supply line.

Read, understand, and follow these notes to construct the

main supply line and pump assembly:
• Fully insert all fittings into the 3/4" black hose during

assembly. See photo and note below.

• Secure all 3/4" black hose and fitting connections

using the 111698 ratchet clamps.

• Position the pump union assembly approximately 6"

above the reservoir cover. Secure with ratchet clamps.

• Position the filter/valve assembly at the reservoir end

of the frame between the crossbars as shown.

• Install filter assembly

according to the water flow

arrow on the filter housing

.

WF3411

ATTENTION:

Use pliers to gently squeeze ratchet

clamps around tubing.

6"

Pump Union

Assembly

WF1530

Elbow

Filter/V

alve

Assembly

WF4130

3/4" PVC

WF3411

WF2153

111074

WF6504A

3/4" Black Hose

WF6504A

3/4" Black Hose

Consult guide included with

the pump for pump fitting

installation.

111074

111698 Ratchet

Clamp

WF6504A

Black Hose

111698

Clamp

Pump Union

Assembly

«
...
17
18
19
20
21
...
»

Содержание Growers Supply HydroCycle 4" Pro NFT
































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: B&K Страницы: 12

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Tablet1000 Series

Бренд: Hantek Страницы: 98

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: Velp Scientifica Страницы: 16

Бренд: Velp Scientifica Страницы: 2

Бренд: Velp Scientifica Страницы: 32

Бренд: Velleman-Kit Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды