FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 31

background image

20

20

112525

Revision date: 01.14.21

Assembly Instructions

Required parts and tools:
•  Channel Lids
•  Drill and 5/16" Drill Bit
•  Tape Measure and Marker

13

PREPARE LIDS FOR 1/4" FEEDER TUBES

There are different ways to drill a 5/16" hole in each lid. For example, lids can be placed in small stacks and drilled

at the same time, or lids can be drilled individually. Here are the main points:
1.  Center each hole approximately 1" to 1-1/4" in from lid end.
2.  Drill only one (1) hole at the supply manifold end for each lid.
3.  Ensure plant holes are staggered when lids are installed. In other words,

do not stack lids to drill feeder tube

hole without considering where lid will be installed.

4. To prevent debris from entering NFT channels,

do not drill lids over NFT channels

. See photo — right.

5. Once lids are prepared, place one on each NFT channel. Stagger plant holes as shown below.

To prevent shavings from dropping

into channel, slide lid out over

channel end (or set lid off to the side)

and drill hole for feeder tube.

1" to 1-1/4"

slide

lid

End of NFT

Channel

1' to 1-1/4"

from end

«
...
18
19
20
21
22
...
»

Содержание Growers Supply HydroCycle 4" Pro NFT
































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: NARGESA Страницы: 50

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: PacBio Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды