FarmTek Growers Supply HydroCycle 4" Pro NFT Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 31

background image

24

112525

Revision date: 01.14.21

System Check

After assembling the 112525 NFT system, take a few minutes to check the

system. Complete these steps.

1.  Verify that all electrical cord ends are outside the reservoir.
2.  Ensure that the supply tubes are fully inserted in the channel lids.
3.  Fill the reservoir with a few inches of water to cover the pump.
4.  Verify that the

WF3310

in-line valve in the main supply tube is open.

5. Plug the water and air pump power cords into an GFCI (Ground Fault

Circuit Interrupter) outlet. Both pumps should turn on.

6. Check each NFT channel to ensure that water is running out each supply

tube and the drain end of each channel.

7.  Check all plumbing connections—main supply line and filter—for leaks.
8.  Check all pvc fittings for leaks.
9.  Look for bubbles in the reservoir to verify that the air is pumping to each air

stone. Remember to always mount the air pump on a surface that is above

the water level. Vibrations of the pump can cause it to move. Make sure

the pump does not fall into the reservoir or other liquids.

10. Once the system has been checked and all adjustments are made, it is

ready for use.

WARNING:

KEEP ALL ELECTRICAL CORDS AND CONNECTIONS

OUT OF THE RESERVOIR. CONSULT THE SERVICES OF A

QUALIFIED ELECTRICIAN TO ADEQUATELY AND SAFELY

CONNECT THE PUMPS TO A POWER SUPPLY.

ALL ELECTRICAL CIRCUITS SHALL BE DESIGNED IN

ACCORDANCE WITH LOCAL AND REGIONAL BUILDING CODES

AND STANDARDS.

System Check

Column reserved for notes.

«
...
22
23
24
25
26
...
»

Содержание Growers Supply HydroCycle 4" Pro NFT
































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply HydroCycle 4" Pro NFT

Бренд: Calistair Страницы: 44

Бренд: Fenton Страницы: 16

Бренд: Naked Страницы: 36

Бренд: Yamaha Страницы: 39

Бренд: Yamaha Страницы: 110

Бренд: Garrick Страницы: 8

CHIEFTAIN E1006

Бренд: Falcon Страницы: 5

CardioCare EKG2000

Бренд: Bionet Страницы: 70

Egatronik 51249

Бренд: Ega Master Страницы: 22

Бренд: NUVE Страницы: 31

Бренд: Sri Страницы: 9

BTL7-P511-M-P-S32/KA Series

Бренд: Balluff Страницы: 16

Бренд: NEBO Страницы: 2

Spectral M950 Q4 Tour

Бренд: SHOWTEC Страницы: 24

Бренд: Ibiza Страницы: 20

Бренд: hager Страницы: 2

Blue Ridge Big Skye I

Бренд: Gorilla Playsets Страницы: 136

Бренд: Farmi Forest Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды