FarmTek FodderPro 2.0 Full Feed System-Wall Mount... Скачать руководство пользователя страница 4

Страница: 4 / 53

111628W

Revision date: 09.25.18

Connecting Multiple Systems to a 2" Main Supply Line

Except for the additional 2" PVC pipe shown in the diagram, each system includes the following components to connect to a 2" main water supply line:

•

(1) WF1386 (PVC 2" Tee)

•

(2) WF3516 (2" Ball Valve)

•

(1) WF2391 (2" x 3/4" Bushing)

RECOMMENDED SPACING

For easy maintenance and access, maintain at least

24" between fodder frames.

ATTENTION: WHEN CONNECTION TWO (2) OR MORE FODDER SYSTEMS TO THE SAME MAIN

SUPPLY LINE, YOU MUST CONNECT THE LINE TO THE TOP OF EACH SUPPLY MANIFOLD.

WF1386

WF3516

2" PVC Pipe

(Additional Purchase Required)

2" PVC Pipe

(Additional Purchase Required)

WF3311 (3/4" Ball Valve)

Included with Fodder System

WF3311 (3/4" Ball Valve)

Included with Fodder System

WF3516

WF2391 (2" x 3/4")

2" PVC Pipe

WF3516

WF2391 (2" x 3/4")

2" PVC Pipe

Содержание FodderPro 2.0 Full Feed System-Wall Mount...






















































Результаты поиска

Содержание FodderPro 2.0 Full Feed System-Wall Mount...

Отзывы:

Похожие инструкции для FodderPro 2.0 Full Feed System-Wall Mount...

Бренды по названию

Популярные бренды

FarmTek FodderPro 2.0 Full Feed System-Wall Mount..., Руководство пользователя

Результаты поиска

Содержание FodderPro 2.0 Full Feed System-Wall Mount...

Отзывы:

Похожие инструкции для FodderPro 2.0 Full Feed System-Wall Mount...

Бренды по названию

Популярные бренды