FarmTek FodderPro 2.0 Full Feed System-Wall Mount... Скачать руководство пользователя страница 19

Страница: 19 / 53

Revision date: 09.25.18

111628W

ASSEMBLE MAIN FRAME: Level and Secure Frame to the Wall

Assembly Instructions

Required Parts:
• 112322 Brackets
• Customer-Supplied Fasteners to secure brackets to the wall

Complete these steps:
1. With assistance, slide the frame assembly

against the wall that it will be attached to

. The upper and lower wall mount tubes should be tight against the

wall when the frame is in the proper position.

2. Determine the drain end of the frame (low end) and set the appropriate frame slope to that end using the 1/2" x 8" levelers (112502) in each base rail. See

the diagrams below.

A slope of 4" to 6" is recommended.

Also, consider the slope of the floor during this step.

NOTE:

An insufficient slope may cause seeds to float and water to pool as it slowly flows toward the drain; a slope that is too great can cause seeds in

freshly seeded channels to wash toward the drain.

SET THE PROPER SLOPE OF THE FODDER FRAME

To ensure that water flows through and properly drains from

the fodder channels, a 4"- 6" slope toward the drain end of

the system is required. Additionally, frame must be level from

side-to-side when viewed from the end. See diagrams on the

next page.

The 111628W fodder frame is equipped with three (3) sets of

levelers—one set at each of the vertical frame assemblies. If

the system is on a sloped concrete pad for example, adjust the

following steps as needed to achieve the slope. Depending on

the slope of the site, it is possible that the levelers will be used

to simply level the frame from side-to-side.

ATTENTION:

Levelers are designed to adjust for minor or

slight variations in the site. When adjusted properly, all levelers

will touch the floor to stabilize the frame. Tighten the locking

nuts to maintain the adjustment and to lock the levelers to the

base rail.

Depending on the site, it may be necessary to

remove the two (2) leveler bolts at the drain (or low end)

of the frame to achieve a 4" to 6" recommended slope.

Photo shows the levelers

as attached to the base

rail of the end frame.

Actual bolt may differ from

what is shown.

Finished Grade

Drain End of the Frame

Adjust to

set a 4"-6"

slope to

drain end.

Adjust bolt to lowest setting

and level frame.

Содержание FodderPro 2.0 Full Feed System-Wall Mount...






















































Результаты поиска

Содержание FodderPro 2.0 Full Feed System-Wall Mount...

Отзывы:

Похожие инструкции для FodderPro 2.0 Full Feed System-Wall Mount...

Бренды по названию

Популярные бренды

FarmTek FodderPro 2.0 Full Feed System-Wall Mount..., Руководство пользователя

Результаты поиска

Содержание FodderPro 2.0 Full Feed System-Wall Mount...

Отзывы:

Похожие инструкции для FodderPro 2.0 Full Feed System-Wall Mount...

Бренды по названию

Популярные бренды