FarmTek FodderPro 2.0 Full Feed System-Wall Mount... Скачать руководство пользователя страница 12

Страница: 12 / 53

111628W

Revision date: 09.25.18

ASSEMBLE MAIN FRAME: Base Rail (1)

Gather the parts and complete the steps that follow to assemble the outer base rail.

Assembly Instructions

Required parts for the base rail:
•  (1) S15P116 Square Tube (plain) for base rail
•  (2) 104625 2-Way Connector and (1) 104626 3-Way Connector
•  FA4482B Tek Screws and 100441 Magnetic Nut Setter

Complete these steps:
1. Slide one 3-way connector onto one end of the S15P116 tube. Center the connector on the

tube and secure using two (2) Tek screws. See FIG. 1 below.

2. Attach one 2-way connector to each end of the tube as shown.

Verify that each connector is

tight to the end of the tube.

Secure using one Tek screw for each connector. Verify that the

length of the assembled tube is 119 1/2".

3. Slide the base rail onto the frame and secure using FA4482B Tek screws (FIG. 2 & 3).
4. Continue with the next procedure.

S15P116

Base Rail

Open end of

connector

Open end of

connector

Length 1

19 1/2"

outside-to-outside

Center this connector on

the base rail and secure

using Tek screws.

ASSEMBLED BASE

RAIL

S15P116

Base Rail

Open end of

connector

FIG. 1

FIG. 2

S15P116

Base Rail

Install so

tube and

2-way fitting

are flush.

End

Frame

Tube

End

Frame

Tube

FIG. 3

Содержание FodderPro 2.0 Full Feed System-Wall Mount...






















































Результаты поиска

Содержание FodderPro 2.0 Full Feed System-Wall Mount...

Отзывы:

Похожие инструкции для FodderPro 2.0 Full Feed System-Wall Mount...

Бренды по названию

Популярные бренды

FarmTek FodderPro 2.0 Full Feed System-Wall Mount..., Руководство пользователя

Результаты поиска

Содержание FodderPro 2.0 Full Feed System-Wall Mount...

Отзывы:

Похожие инструкции для FodderPro 2.0 Full Feed System-Wall Mount...

Бренды по названию

Популярные бренды