FARMSCAN 74V1 Скачать руководство пользователя страница 29

Страница: 29 / 103

February 2017

www.farmscanag.com

AM-74V1-4

Device Menu Overview

ALARMS (3) – OVERVIEW

Alarm Title

Title of the Alarm, which indicates what the alarm is monitoring.

Alarm Tripped Status

Indicates whether the Alarm has been tripped.

An alarm is ‘tripped’ if it has gone into the Alarm state and has not been reset yet.

Alarm State Status

Indicates whether the Alarm is in Alarm or OK state.

An Alarm is in the Alarm state when it has exceeded a given limit set for the Alarm, e.g.
speed going over a maximum speed or tank level going below a minimum level.

Alarm Active/ Inactive

Select this checkbox to activate or deactivate the Alarm.

WARNING: Inactive Alarms will not indicate when their set limits have been exceeded.

A tick in the box indicates the Alarm is active.

Scroll Up/ Down buttons

NOTE:

These buttons will be visible if multiple Alarms exist and cannot be displayed on one screen.

If more than 5 Alarms are listed in the table then the Up/ Down buttons will allow the user
to scroll through the table to display all Alarms.

Содержание 74V1








































































































Результаты поиска

Содержание 74V1

Отзывы:

FARMSCAN 74V1, Руководство оператора, Страница: 29 / 103

Результаты поиска

Содержание 74V1

Отзывы: