Farm King VT3290 Скачать руководство пользователя страница 79

Страница: 79 / 232

Assembly - VT3000 Series

Figure 127

Position scrapers (Item 1) on the scraper bar (Item
2)

[Figure 127]

Align one scraper behind each blade of the gang
section. The scrapers should be almost touching
the blades.

Attach each scraper using one 1/2” u-bolt, two
1/2” lock washers, and two 1/2” hex nuts (Item 3)

[Figure 127]

. Do not tighten at this time.

Make sure to use correct LH or RH scrapers for
the gang sections. The scraper tip should angle
down toward the center of the blade.

Continue installing the remaining scrapers.

Check that all scrapers are installed and positioned
correctly.

Tighten all hardware.

SCRAPER AND SCRAPER BAR

Standard Scraper Assembly

Figure 126

Align one scraper bar (Item 1)

[Figure 126]

of the

correct length with the appropriate gang section.

Position the scraper bar underneath the mounting
plates (Item 2)

[Figure 126]

at each hanger on the

gang section.

Attach the scraper bar to the mounting plate using
one 1/2” u-bolt, two 1/2” lock washers, and two
1/2” hex nuts (Item 3)

[Figure 126]

NOTE: Mount (Item 2) [Figure 126] is positioned so

scraper bar is located at rear of gangs.

Continue installing the remaining scraper bars
for each gang section. Do not tighten hardware at
this time.

IMPORTANT

Scrapers are pre-installed on the scraper bars at
the factory.

Содержание VT3290









































































































































































































































Результаты поиска

Содержание VT3290

Отзывы:

Farm King VT3290, Руководство оператора и каталог запасных частей, Страница: 79 / 232

Результаты поиска

Содержание VT3290

Отзывы: