manualshive.com logo in svg

Farm King VT3290, Руководство оператора и каталог запасных частей, Страница: 57 / 232

Поделиться
Скачать
Farm King VT3290 Скачать руководство пользователя страница 57

Assembly - VT3000 Series

55

Install one 1-9/32” ID x 2” OD x 1/4” washer onto 
the pin, then push the cylinder pin through the 
second bracket of the cylinder mount.

Install another 1-9/32” ID x 2” OD x 1/4” washer 
(Item 1) on the end of the cylinder pin and secure 
with two cotter pins (Item 2) 

[Figure 92]

. Then 

install the cylinder pin through the mounting 
bracket and clevis.

Repeat for three remaining wing cylinders.

Enter the tractor and start the engine.

Using the tractor’s auxiliary controls, cycle the 
hydraulic cylinders on the VT3000 to test for 
correct operation.

Fully raise the VT3000 frame and fully unfold RH 
& LH wings.

Turn tractor engine off and exit the tractor.

Close shut-off valves.

Purging / Rephasing Hydraulic System

IMPORTANT

Failure to purge hydraulic system of air or rephase 
depth control cylinders, could result in uneven 
tilling depth across the width of the machine, as 
one or more cylinders may creep, “bounce” or 
move erratically.

Purging Hydraulic System

Following assembly and prior to placing the 
VT3000 into field service, it is important the series 
depth control cylinders be purged of air that has 
been trapped in the system.

Use the following procedure to purge trapped air 
from the hydraulic system:

1.  Connect the VT3000 hydraulics to tractor and 

remove all depth control stops.

2.  Raise VT3000 to extend lift cylinders fully and hold 

hydraulic lever in the UP position for (3) three 
minutes.

3.  Lower VT3000 to retract lift cylinders fully.

NOTE: All lift cylinders may not fully retract.

4.  Raise VT3000 again and hold hydraulic lever in the 

UP position for another (3) three minutes.

Rephasing Hydraulic System

Following the initial purging of the series hydraulic 
system, it is a recommended practice to rephase 
the depth cylinders several times each day by 
holding hydraulic lever in the UP position for five 
to ten seconds. This can be normally done when 
implement is raised to make a turn at the end of 
the field.

IMPORTANT

Hydraulic pressure must be relieved at the end of 
the day and prior to uncoupling from tractor.

Содержание VT3290









































































































































































































































Отзывы:

Нет отзывов