Farm King VT3290 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 232

Farm King VT3290 Скачать руководство пользователя страница 14

Safety - VT3000 Series

12

Use Safety Rules

• Read and follow instructions in this manual and the

tractor’s Operators Manual before operating.

• Under no circumstances should young children be

allowed to work with this equipment.

• This equipment is dangerous to children and persons

unfamiliar with its operation.

• If the elderly are assisting with work, their physical

limitations need to be recognized and accommodated.

• Stay clear of overhead power lines when raising or

lowering the wings. Electrocution can occur without
direct contact.

• Check for overhead and / or underground lines before

operating equipment (if applicable).

• In addition to the design and configuration of

equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involved
in the operation, transport, maintenance and storage
of equipment.

• Check that the equipment is securely fastened to the

tractor.

• Make sure all the machine controls are in the

NEUTRAL position before starting the machine.

• Operate the equipment only from the operator’s

position.

• Operate the equipment according to the Operator’s

Manual.

• When learning to operate the equipment, does it at

a slow rate in an area clear of bystanders, especially
small children.

• DO NOT permit personnel to be in the work area

when operating the equipment.

• The equipment must be used ONLY on approved

tractors.

• DO NOT modify the equipment in any way.

Unauthorized modification may impair the function
and / or safety and could affect the life of the
equipment.

• DO NOT make any adjustments or repairs on the

equipment while the machine is running.

• Keep shields and guards in place. Replace if damaged.
• Always relieve the pressure in hydraulic system

and close both hydraulic lockup valves when not in
operation.

• Always stay clear of the folding wing when it is being

raised, lowered or placed in the folded position.

• When operating on hillsides, use extreme care. The

tractor may tip over if it strikes a hole, ditch or other
irregularity.

«
...
12
13
14
15
16
...
»

Содержание VT3290









































































































































































































































Отзывы:

Нет отзывов