Farm King VT3290 Скачать руководство пользователя страница 122

Страница: 122 / 232

Maintenance - VT3000 Series

120

AXLES

Wheel Bolts Torque

IMPORTANT

CHECK WHEEL BOLTS AFTER:

First five hours of field operation.

First twenty-five hours of field operation.

First fifty hours of field operation.

Every two hundred hours of operation.

REPEAT PROCEDURE IF A WHEEL IS REMOVED
OR REINSTALLED

Tighten wheel bolts:

• Main Frame - 240 ft.-lb. (325 N•m)
• Wing Frame - 150 ft.-lb. (203 N•m)

Tire / Wheel Replacement

Periodically check tires for cuts, bulges and
damaged rims.

WARNING

AVOID INJURY OR DEATH

Before you leave the operator’s position:

Always park on a flat level surface.

Place all controls in NEUTRAL.

Engage the park brake.

Stop the engine and remove the key.

Wait for all moving parts to stop.

Park the tractor / equipment on a flat level surface.

Place all controls in neutral, engage the park
brake, stop the engine and wait for all moving
parts to stop. Leave the operator’s position.

Fully raise wings into transport position and
secure with safety chain.

WARNING

If wings are folded into transport position, always
install a wing stop links between each wing frame
and main frame to prevent wings from falling.

WARNING

AVOID INJURY OR DEATH

Always chock tires before performing any
maintenance or service.

NOTE: Place blocks / stands under the frame to

secure the VT3000 when tire / wheel is
raised off the ground.

Remove the eight wheel bolts on wings or wheel
nuts on main frame and remove the tire / wheel.

Place chock blocks behind and in front of the
opposite tire to be removed.

Raise axle frame with jack until the tire / wheel is
slightly off the ground.

Figure 176

Install the new tire with the valve stem facing out.

Reinstall eight wheel bolts (Items 1)

[Figure 176]

Содержание VT3290









































































































































































































































Результаты поиска

Содержание VT3290

Отзывы:

Farm King VT3290, Руководство оператора и каталог запасных частей, Страница: 122 / 232

Результаты поиска

Содержание VT3290

Отзывы: