Farm King VT3290 Скачать руководство пользователя страница 75

Страница: 75 / 232

Assembly - VT3000 Series

Outside Gang Section Assembly

NOTE: The following procedure shows installing

the left front outside gang section. The
procedure is the same for all outside gang
sections.

Figure 117

Locate the front left, outside gang section. (Refer
to the gang section diagram for the correct
corresponding letter and orientation.)

Install straps (Item 1) around the gang section
(Item 2)

[Figure 117]

Connect the straps to an approved lifting device.

Raise and move the gang section to the assembly
area.

Lower the gang section onto the ground in front
of the left wing frame.

Remove straps from the lifting device.

NOTE: Do not remove straps from around the gang

section.

Route straps in front and behind the wing gang
beam, straddling the wing gang beam.

Connect the straps to an approved lifting device.

NOTE: When adjusting / aligning gang sections,

always maintain the designated blade
spacing between gang sections.

Raise the gang section and move inner blade
towards the inside gang section (approximate
blade spacing distance). Lower gang section to
the ground.

NOTE: The following image may not show your

gang section exactly as it appears but the
procedure is correct.

IMPORTANT

Hanger bracket must be sitting square with gang
beam before tightening carriage bolts.

Figure 118

Locate three 3/4” x 8” carriage bolts, three 3/4”
lock washers and three 3/4” nuts per bearing
hanger (Item 1)

[Figure 118]

(each hanger bracket).

Raise the gang section just below the gang beam.

Position one hanger mounting plate (Item 2) on
top of the gang beam (above hanger bearing).
Install one hanger / scraper bar mounting plate
(Item 3)

[Figure 118]

under the hanger bearing.

Install the three 3/4” x 8” carriage bolts down
through the hanger mounting plate and hanger /
scraper bar mounting plate.

Install 3/4” lock washers and 3/4” nuts (Item 4)

[Figure 118]

onto the carriage bolts. Do not tighten

at this time.

Repeat for remaining hanger bearings on the
gang section.

Содержание VT3290









































































































































































































































Результаты поиска

Содержание VT3290

Отзывы:

Farm King VT3290, Руководство оператора и каталог запасных частей, Страница: 75 / 232

Результаты поиска

Содержание VT3290

Отзывы: