FANOX SIA D Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 117

FANOX SIA D Скачать руководство пользователя страница 53

www.fanox.com

SIA-D_

Rev. 07

53 / 117

ISO 9001:2008

5.12. Modbus RTU Protocol

The protocol documentation and the modbus memory map are shown in the appendix to this manual.

5.13. Test Program

The SIA-D equipment has a test menu that can be used to check the operation of the signalling
components (LEDs and magnetic indicators) and the outputs. It is important to point out that the
operation of the outputs is not guaranteed if the test is performed with the battery.

The following table shows the components that can be tested, along with their status depending on
whether they are activated or deactivated:

Vaux power LED

Deactivated

Vaux LED off

Activated

Vaux LED blinking

Self-power LED

Deactivated Self-power

LED

off

Activated

Self-power LED blinking

Battery LED

Deactivated Battery

LED

off

Activated

Battery LED blinking

“50/51P” magnetic indicator

Deactivated

“50/51P” magnetic indicator deactivated (black)

Activated

“50/51P” magnetic indicator activated (orange)

“50/51N” magnetic indicator

Deactivated

“50/51N” magnetic indicator deactivated (black)

Activated

“50/51N” magnetic indicator activated (orange)

“External trip” magnetic indicator

Deactivated

“External trip” magnetic indicator deactivated (black)

Activated

“External trip” magnetic indicator activated (orange)

Output 1

Deactivated Output

1

deactivated

Activated

Output 1 activated

Output 2

Deactivated Output

2

deactivated

Activated

Output 2 activated

Output 3

Deactivated Output

3

deactivated

Activated

Output 3 activated

Output 4

Deactivated Output

4

deactivated

Activated

Output 4 activated

The following key sequence is used to gain access to the test menu: from the main menu, press the
keys “

◄

”, “

▼

”, and “

►

” in sequence and then press and hold the "OK" key until the "Test menu"

«
...
51
52
53
54
55
...
»

Содержание SIA D






















































































































Отзывы:

Нет отзывов