manualshive.com logo in svg

FANOX SIA D, Руководство пользователя, Страница: 52 / 117

Поделиться
Скачать
FANOX SIA D Скачать руководство пользователя страница 52

   

 

 

 

www.fanox.com

                                     SIA-D_

Rev. 07

      

 

52 / 117

 

 

 

ISO 9001:2008 

stop bit). The protocol map and documentation that are used are attached in an appendix to this 
manual. 

The adapter (KITCOM) can be connected to this communications port to supply the equipment with 
an external battery. It should be pointed out that this port can be used simultaneously for 
communication, even when the equipment is being powered by an external battery. 

The PC earth should be connected to the same earth as the relay to avoid communication problems. 

 

5.11.  Rear Communication. RS485 

An option exists to fit the SIA-D with a rear communications port RS485, which must be specified 
when the model is selected. 

The RS485 port output has three terminals (+,- and GND), located on the rear of the equipment. The 
protocol that is used is Modbus RTU (19200 -8bit – no parity – 1 stop bit).  

The protocol map and documentation that are used are attached in an appendix to this manual. 

This port can be used to continuously monitor the equipment from a remote PC or SCADA system.  
Up to 32 pieces of equipment can be connected to one bus; each piece with a different modbus 
address. The equipment modbus address can be configured using the SIcom program. 

To minimise communication errors as a result of noise, the use of a stranded and shielded cable is 
recommended for the physical connection. All of the + terminals on one side, and all of the - 
terminals on the other must be connected together in order to make the connection. 

If a 3 strand cable is used for communication, the GND terminals must be connected to the earth 
cable. 

If a 2 strand cable is used for communication, the GND terminals must be connected to the shielding.  
The shielding must be connected to the GND at only one point to avoid circular currents.  

Resistors should be used at each end if very long cables are used. The best solution for avoiding 
reflection is to install resistors at both ends of the cable. The ohm value of these resistors must be 
equal to the cable impedance value. 

Fibre optics can be used in very aggressive environments, and they are connected by using the 
corresponding converters. 

Connection diagram for a RS485 bus: 

SIA-E

+

-

gnd

SIA-E

+

-

gnd

SIA-E

+

-

gnd

C

R

C

R

+

-

gnd

RS485/RS232

RS232

 

Содержание SIA D






















































































































Отзывы:

Нет отзывов