manualshive.com logo in svg

FAAC DAAB EP104 V4.08, Руководство пользователя, Страница: 25 / 60

Поделиться
Скачать
FAAC DAAB EP104 V4.08 Скачать руководство пользователя страница 25

CHANNEL LIST DAAB AUTOMATIC CONTROL UNIT EP104 4.08

25

Channel list edition 1 for EP104 version 4.08

No. 

Name

Range

Factory

Setting

L120*

Placement of motor 2, viewed from the motor side

0-2

2

0

Disabled

1

Left

2

Right

L121*

Position readout, motor 2

000-360 degrees

L122*

Open position angle, motor 2

145-330 degrees

260

L123*

Closed position angle, motor 2

015-180 degrees

90

L126*

Angle for limited opening, motor 2

0-200 degrees

45

L127*

Angle for the disconnection of  safety edges, load 

guard and photocells from the end of  the closing 

movement, motor 2 in combination with C436, C341 

and C448

0-30 degrees

0

L128*

Angle for the disconnection of  vehicle loops from the 

end of  the closing movement, motor 2 in combination 

with d141 or d241

0-45 degrees

0

L311

Time readout for motor 1

00.1-99.9 seconds

L312** Set time for motor 1

00.1-99.9 seconds

00.1

L321

Time readout for motor 2

00.1-99.9 seconds

L322** Set time for motor 2

00.1-99.9 seconds

00.1

* = Only displayed if  L002 are set to 1.

** = Only displayed if  L001 and/or L002 are set to 2 or 3.

Содержание DAAB EP104 V4.08





























































Отзывы:

Нет отзывов