Extron electronics DMP 64 Plus, Руководство пользователя

Страница: 62 / 99

DMP 64 Plus • SIS Configuration and Control 55
Command ASCII command
(host to device) Response
(device to host) Additional description
Audio Group Master Commands
NOTES:
•
For information on configuring groups, see Configure Groups on page 17 or the DSP Configurator Help File .
•
A group must have assigned members for these commands to have an effect.
•
For
X6@
, a positive (+) value is assumed unless a negative (-) value is specified.
•
If entering an
X6@
value outside the valid range for the group or outside the soft limits, the DMP 64 responds with an
E13
error (invalid parameter).
• X6@
,
X6#
, and
X6$
values can be sent without leading zeroes.
Set a group fader value E
D X6! * X6@ GRPM
}
GrpmD X6! * X6@
] Set a group fader to a
value of
X6@
.
Example:
E D2*-239GRPM
}
GrpmD2*-293
] Set group 2 fader control
to -29.3 dB.
Increment a group fader
value
E D
X6!
*
X6#
+GRPM
}
GrpmD
X6!
*
X6@ ]
Increase the level of
X6!
by
X6#
dB.
Example:
E D2*30+GRPM
}
GrpmD2*-263
] Raise the group 2 fader
3 dB from -29.3 dB (set in
example above) to -26.3
dB.
Decrement a group
fader value
E D
X6!
*
X6#
-GRPM
}
GrpmD
X6!
*
X6@ ] Decrease the level of the
X6!
group fader by
X6#
dB.
View the group fader
value
E D
X6!
GRPM
}
GrpmD
X6!
*
X6@ ] In verbose modes 0 and 1,
the response is simplified
to
X6@ ]
.
Mute a group
E D
X6!
*1GRPM
}
GrpmD
X6!
*1
] Mute all blocks in group
X6!
.
Unmute a group
E D
X6!
*0GRPM
}
GrpmD
X6!
*0
] Unmute all blocks in group
X6!
.
View a group mute
value
E D
X6!
GRPM
}
GrpmD
X6!
*
X6) ]
For group masters,
X6)
is
always expressed as an
unsigned or negative value.
Set soft limits E
L
X6!
*
X6$
upper
*
X6$
lower
GRPM
}
GrpmL
X6!
*
X6$
*
X6$ ] Set the groups soft limits to
X6$
upper and
X6$
lower .
Example: E
L2*60*-60GRPM
}
GrpmL2*60*-60
] Set the upper soft limit for
the group 2 fader to +6.0
dB and the lower limit to
-6.0 dB.
KEY: X6)
= Mute status:
0
= Unmute
1
= Mute
X6!
= Group master group number:
1
through
64
X6@
= Group fader setting: dB value in 0.1 dB steps, using negative numbers and eliminating decimal places using a 10x
multiplier. -100.0dB to +80.0 dB is represented by
-1000
to
800
. The valid range depends
on the type of gain or trim block assigned to the group number (
X6!
).
X6#
= Group fader increment/decrement: dB value in 0.1 dB steps to raise or lower a group fader.
Gain uses 10x multiplier (+10 dB =
100
+). + or - goes after the number.
X6$
= Group fader soft limit: dB value in 0.1 dB steps. Gain uses 10x multiplier (+10 dB =
100
+).