Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 220 | Manualshive

Страница: 220 / 413

background image

4 When power is connected, verify that the PSU LED and RPS LED (if applicable) turns green.

When both LEDs have turned green, follow the instructions in

Connecting Network Interface Cables

page 220.

If the PSU and RPS LEDs do not turn green, see the

Switch LEDs

topic for your switch model (in the

ExtremeSwitching Switches

on page 10 section) for troubleshooting information.

Connecting Network Interface Cables

Use the appropriate type of cable to connect the ports of your switch to another switch or router.

Cable Type

Maximum Distance

CAT5E

55 meters

CAT6

55 meters

CAT6A

100 meters

Working carefully, one port at a time, do the following:

1 Verify that you have identified the correct cable for the port.
2 Use an alcohol wipe or other appropriate cleaning agent to clean the cable connectors; make sure

they are free of dust, oil, and other contaminants.

3 If you are using optical fiber cable, align the transmit (Tx) and receive (Rx) connectors with the

correct corresponding connectors on the switch or the I/O module.

4 Press the cable connectors into their mating connectors on the switch or I/O module until the cable

connector is firmly seated.

5 Repeat the preceding steps for the remaining cables on this or other switches or I/O modules.
6 Dress and secure the cable bundle to provide appropriate strain relief and protection against bends

and kinks.

Performing Initial Management Tasks

When you set up a switch for the first time, you must connect to the console to access the switch and
log in to perform initial security configuration.

Check

http://ezcloudx.com/supportedhardware

to see what switch models can be managed with

ExtremeCloud. If your switch is entitled for management by ExtremeCloud, you can optionally use the
installation instructions at

http://ezcloudx.com/quickstart

.

Otherwise, to perform normal setup and configuration, follow the instructions in these topics:

•

Connecting a Switch to the Management Console

on page 221

•

Logging in for the First Time

You can also:

•

Configuring the Switch's IP Address for the Management VLAN

•

Configuring ExtremeXOS on the Switch

on page 223

Installing Your Extreme Networks Switch

ExtremeSwitching and Summit Switches: Hardware Installation Guide

220

«
...
218
219
220
221
222
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: Eaton Страницы: 12

Бренд: Radial Engineering Страницы: 12

Бренд: vantiva Страницы: 58

Hub M50 Mesh Cube

Бренд: Xunison Страницы: 11

Instant On 1930 24G 4SFP/SFP+l

Бренд: Aruba Страницы: 48

Бренд: UniFi Страницы: 8

Бренд: Micrel Страницы: 15

Бренд: PABX Страницы: 46

Бренд: N-Tron Страницы: 15

IMI Sensors 691A80

Бренд: PCB Piezotronics Страницы: 15

Бренд: Hored Страницы: 4

SENSALINK SENLSS V2

Бренд: Thorn Страницы: 2

Бренд: Shure Страницы: 3

EWS-series EWS2910P-Kit-300

Бренд: EnGenius Страницы: 6

Бренд: PABX Страницы: 16

Бренд: CYP Страницы: 24

Бренд: Hi-SCOM Страницы: 22

BIT-2100 Series

Бренд: Bitifeye Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды