Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 313

Страница: 313 / 413

4 Push the latching tab to the left as you pull outward on the handle to disengage the power supply

internal connectors.

Figure 250: Removing a DC Power Supply

5 Carefully slide the power supply the rest of the way out of the switch.

Removing a Switch from a Rack

Before removing a switch from a rack, verify that:

•

All removable power supplies have been removed. See

Removing an AC Power Supply

on page 311

Removing a DC Power Supply

on page 312.

•

The switch has been disconnected from any redundant power supplies.

•

The switch has been disconnected from all other sources of electrical power.

Note
Read the following steps thoroughly before you attempt to remove a switch from a rack.

To remove a switch from a rack, follow these steps:

1 Support the switch while you remove the rack-mounting screws that hold the front mounting

brackets in place against the rack posts.

2 Remove the switch from the rack.

•

For two-post installations, carefully slide the switch out of the rack.

•

For four-post installations, carefully slide the switch forward out of the cabinet and off the rear
mounting brackets.

See the following figures.

Removing Switches from Service

ExtremeSwitching and Summit Switches: Hardware Installation Guide

313

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching X440-G2 Series, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды