Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 413

background image

Table 43: Summit 715 W AC Power Supply LED Status Indications

IN_OK
(Green)

OUT_OK
(Green/RED)

Description

Off

Off

No AC input power connection or low AC voltage.

On

Off

AC input good, 54V output disabled.

On

(Red) On

AC input good, output (54V) fault.

On

(Green) On

AC input good, DC outputs in spec.

Summit 750 W AC Power Supply

The Summit 750 W AC power supply is used in the EPS-C2 external power system (see

Redundant Power System

on page 95). Each installed Summit 750 W AC power supply can provide up

to 380 watts of PoE power budget.

The Summit 750 W AC power supply has the status LEDs listed in the following table.

Table 44: Summit 750 W AC Power Supply LED Status Indications

Label and Color

State

Meaning

AC OK
Green

Off

No AC input

On

AC input is good.

DC OK
Green

Off

Both DC outputs (55 V and 12 V) are bad or not enabled.

Blinking

One output is enabled and good; the second output is bad or not enabled.

On

Both the 55 V and 12 V outputs are enabled and good.

ALM
Red

Off

No fault condition exists.

Blinking

Power supply alert: power supply is likely to fail because of a developing fault,
such as abnormal thermal conditions or poor fan performance.
or
One output (55 V or 12 V) is bad.

On

Both outputs (55 V and 12 V) are bad.
Power supply is receiving 3.3 VSB from the system. (AC OK and DC OK are off.)
Thermal shutdown, fan failure, or any fault condition when both 55 V and 12 V are
turned OFF.

750 W AC and DC Power Supplies

750 W power supplies are available for the ExtremeSwitching X695 switch in the following models:

•

750W AC power supply - front-to-back airflow (part no. XN-ACPWR-750W-F)

•

750W AC power supply - back-to-front airflow (part no. XN-ACPWR-750W-R)

Power Supplies for Use with Your Switch

ExtremeSwitching and Summit Switches: Hardware Installation Guide

108

«
...
106
107
108
109
110
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: wavin Страницы: 4

S5560S-EI Series

Бренд: H3C Страницы: 37

OfficeConnect WX4400

Бренд: 3Com Страницы: 528

NAMUR BES G06MD-GNX10B-EV02-EEX

Бренд: Balluff Страницы: 56

Бренд: Ableconn Страницы: 16

DSR Series DSR1030

Бренд: Avocent Страницы: 8

SICOM3432G Series

Бренд: KYLAND Страницы: 29

Бренд: Cabletron Systems Страницы: 54

Бренд: TESmart Страницы: 4

Бренд: IDT Страницы: 158

Бренд: DX Engineering Страницы: 4

Бренд: Kramer Страницы: 11

Бренд: BERNSTEIN Страницы: 38

Бренд: serverLink Страницы: 2

Бренд: Black Box Страницы: 2

Бренд: Edimax Страницы: 8

TK-423K - USB/PS/2 KVM Switch

Бренд: TRENDnet Страницы: 14

Бренд: Little Giant Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды